How To Hack Wifi WPA And WPA2 Without Using Wordlist In Kali Linux OR Hacking Wifi Through Reaver

Hello Friends Today I Am Going To Show You How To Hack Wifi Without Using Wordlist Or You Can Call it as Hacking Wifi Password Using Reaver Method

THIS IS FOR EDUCATIONAL PURPOSE ONLY, I AM NOT RESPONSIBLE FOR ANY ILLEGAL ACTIVITIES DONE BY VISITORS, THIS IS FOR ETHICAL PURPOSE ONLY

Requirements :

1)      Kali Linux – Operation System In Your System Or In Your Flash Disk (USB Pendrive)

2)      4GB or Above Pendrive

3)      Kali Live Boot

3)      Wifi networks near by with Excellent Signal to make hacking faster

1)      Click Here to download KaliLinux

2)      Click Here to See How To Make Kali USB Live Boot

Click Here To Learn All Methods And Types of Wifi Hacking

Limitations:

1) Can hack only wps Enabled Routers

2) Cannot hack WPS Turned ON Routers

What is WPS : :

WPS Means Wifi Protected System, This Is a Different Type of security system which is enabled for some routers, it is the best method to hack wifi , But it does have Limitations, they are some routers with wps enabled are secured by another security called “AP RATE LIMITING” if you see this just leave that network and go to another network.

1) Till now no one found any method to break that security system, may be in my later posts I will try to post how to break that security system

2) Wpa And Wpa2 Networks can only be hacked using wordlist, Which uses Brute Force Attack Or Dictionary Attack in which probability of getting password is only 35%

3) But In Reaver Method Probability is 100% (Only If AP Rate Limiting Is Not Available)

4) So it is better to go for reaver method if wps is available

5) It consumes less time than Brute Force Attack Or Dictionary Attack

6) If the network that you want to hack has excellent signal and if your system is in good condition, then the hack completes in 5 – 18 Hours.

Now Just Follow My Snapshots

Step 1: Open Your Terminal And Type “Ifconfig ’’ And Press Enter to check your Interface status

Step 2: Here I will be selecting wlan0 as my interface

And the Next Command Is “airmon-ng start wlan0”

You Should See Something Like This

Then you can see all the available supplicants and kill them By Using Kill Command

Note : there are 2 methods for going into the next step

1) By Using Kill Command and Stopping the Wlan0 Supplicants

2) By Using the Command "airodump-ng mon0" instead of kill and "airodump-ng wlan0" Here i am using Kill Command, Either way we can continue

Now Type The Following Command "airodump-ng wlan0"

Here you can see all the available wifi networks

Press “CTRL + C” To Stop The Search

Now Type “wash –i mon0”

this command is used to see all the available wps enabled networks among the available networks

Here you will be shown all "wps" Enabled networks

Press “CTRL +C” To Stop The Search And Select The Network That You Want To Hack

Copy the bssid of the network that you want to hack

Now use The reaver Command

“reaver –i mon0 –b bssid -vv”

Here bssid = the mac address or the bssid that you copied earlier
mon0= Interface (you can use either wlan0 or mon0 account to the interface that we started earlier)

Now what you have to do is just wait till it reaches 100%

After reaching 100% You can see the password of that network, as it takes a lot of time I am not able to show you the password of that network. But I will guarantee you that this is the best and easiest way to hack wifi wpa and wpa2 password

Now Almost all of the routers come with WPS Turned ON.

This is the AP RATE LIMITING SECURITY SYSTEM

If you face this Error, most likely you should stop using this particular method and go for Evil Twin Method, Which can Hack any router but with user Interference.

The Reason for getting this Error is WPS Protection is turned "ON" on the victim's Router. We can not this kind of router's using Reaver